特种油气藏 ›› 2021, Vol. 28 ›› Issue (6): 137-143.DOI: 10.3969/j.issn.1006-6535.2021.06.018

• 钻采工程 • 上一篇    下一篇

斧形PDC齿破岩规律数值模拟研究

邹德永1, 陈雅辉1, 赵方圆2, 崔煜东3   

  1. 1.中国石油大学(华东),山东 青岛 266580;
    2.中国石油集团渤海钻探工程有限公司,河北 廊坊 065007;
    3.中国石化胜利油田分公司,山东 东营 257015
  • 收稿日期:2020-10-12 修回日期:2021-09-17 出版日期:2021-12-25 发布日期:2022-02-16
  • 作者简介:邹德永(1962—),男,教授,博士生导师,1984年毕业于华东石油学院钻井工程专业,2004年毕业于石油大学(华东)油气井工程专业,获博士学位,现主要从事油气井工程方面的教学和研究工作。
  • 基金资助:
    国家科技重大专项“海上油气田关键工程技术”(2016ZX05033-004)

Study on Rock Breaking Rules of Axe-shaped PDC Cutter with Numerical Simulation

Zou Deyong1, Chen Yahui1, Zhao Fangyuan2, Cui Yudong3   

  1. 1. China University of Petroleum (East China), Qingdao, Shandong 266580, China;
    2. CNPC Bohai Drilling Engineering Company Limited, Langfang, Hebei 065007, China;
    3. Sinopec Shengli Oilfield Company, Dongying, Shandong 257015, China
  • Received:2020-10-12 Revised:2021-09-17 Online:2021-12-25 Published:2022-02-16

摘要: 斧形PDC齿具有独特的齿形,在破岩实验中表现出更好的破岩性能。但斧形PDC齿破岩规律和工作参数及齿形的优选方法不明确。因此,利用ABAQUS软件建立了斧形PDC齿切削岩石的三维有限元模型,通过有限元数值模拟方法分析后倾角、斧刃角对斧形PDC齿破岩效果的影响。结果表明:后倾角为15 °时,斧形PDC齿破岩效率最高;在后倾角相同的情况下,斧刃角越小,切向裂纹越易于向岩石内部发展,最优斧刃角为110 °。根据模拟结果,优化了斧形PDC齿钻头外形参数,并在现场试验中获得较好的效果。该研究结果可为斧形PDC齿钻头优化设计提供重要依据。

关键词: 斧形PDC齿, 后倾角, 斧刃角, 破岩规律

Abstract: Axe-shaped PDC cutter is of special shape and presents better breaking performance in rock breaking experiment. However, the rock breaking rules of axe-shaped PDC cutter and the optimization method of its working parameters and shape are ambiguous. Therefore, a three-dimensional finite element model of cutting rock with axe-shaped PDC cutter was established with ABAQUS software, and the effects of back dip angle and axe edge angle on the rock breaking effect of axe-shaped PDC cutter were analyzed by finite element numerical simulation method. The results showed that the rock breaking efficiency of the axe-shaped PDC cutter was the highest when the back dip angle was 15 °; with the same back dip angle, the smaller the axe edge angle was, the easier the tangential crack was to propagate inside the rock, and the optimal axe edge angle was 110 °. According to the simulation results, the shape parameters of the bit with axe-shaped PDC cutter were optimized, and good results were obtained in the field test. The results of the study provide an important basis for the optimal design of the bit with axe-shaped PDC cutter.

Key words: axe-shaped cutter of PDC bit, back dip angle, axe edge angle, rock breaking law

中图分类号: