稠油热采井射孔孔眼应力分析及影响因素

doi:10.3969/j.issn.1006-6535.2024.01.020

特种油气藏 ›› 2024, Vol. 31 ›› Issue (1): 152-158.DOI: 10.3969/j.issn.1006-6535.2024.01.020

稠油热采井射孔孔眼应力分析及影响因素

梁疆岭¹, 杨洪¹, 苏宏益¹, 林铁军², 赵朝阳², 但晗²

1.中国石油新疆油田分公司,新疆克拉玛依 834000;
2.西南石油大学油气藏地质及开发工程全国重点实验室,四川成都 615000

收稿日期:2023-03-20 修回日期:2023-12-17 出版日期:2024-02-25 发布日期:2024-04-18
通讯作者: 林铁军(1980—),男,研究员,2003年毕业于西南石油学院石油工程专业,2009年毕业于西南石油大学油气井工程专业,获博士学位,现从事油气井工程力学及仿真、钻完井技术及井下工具研发、稠油地热井热流固多场耦合方面的研究工作。
作者简介:梁疆岭(1983—),男,高级工程师,2007年毕业于西南石油大学石油工程专业,现从事新疆油田井下作业等相关工作。
基金资助:
国家自然科学基金面上项目“深层页岩多级分段压裂套管变形容忍限研究”(52274042)

Stress Analysis and Influencing Factors of Perforation in Heavy-Oil Thermal Recovery Wells

Liang Jiangling¹, Yang Hong¹, Su Hongyi¹, Lin Tiejun², Zhao Chaoyang², Dan Han²

1. PetroChina Xinjiang Oilfield Company, Karamay, Xinjiang 834000, China;
2. National Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University, Chengdu, Sichuan 615000, China

Received:2023-03-20 Revised:2023-12-17 Online:2024-02-25 Published:2024-04-18

摘要/Abstract

摘要： 针对稠油热采井生产过程中,射孔井段套管频繁出现损伤断裂的问题,基于弹塑性和热力学理论,采用有限元方法建立注汽—焖井—生产过程射孔套管有限元热力学耦合模型,对各阶段射孔套管应力分布特征进行研究,并开展不同射孔参数下射孔套管强度影响规律分析。研究表明:生产过程中射孔孔眼位置出现明显应力集中现象,在温差及内外压差等共同作用下,注采前期套管应力最大可达498.16 MPa,并逐渐产生塑性失效现象,当注采作业完成时,套管塑性失效现象最严重;随着射孔相位角增大,射孔密度对Mises应力值的影响逐渐减小,而套管孔眼最大应力与射孔相位角成反比关系。该研究对延长稠油热采井射孔套管使用年限和保障正常生产作业具有十分重要的意义。

关键词: 稠油热采, 套管损伤, 射孔孔眼, 套管强度,应力集中

Abstract: Aiming at the problems of frequent damage and fracture of perforated casing during the production process of thermal recovery wells, based on the theory of elasticity-plasticity and thermodynamics, a finite element thermodynamic coupling model of perforated casing during the process of steam injection-stewing-production was established by using finite element method to research the stress distribution characteristics of the perforated casing in each stage, and analyze the strength influence rule of the perforated casing under different parameters of perforated casing. The study shows that the obvious stress concentration occurs at the location of the injection hole boreholes during the production process. The casing stress could reach up to 498.16 MPa in the early stage, and the plastic failure occurs gradually under the joint action of the temperature difference and the internal and external pressure difference. The casing plastic failure is the most serious once the injection and production operation is completed. The influence of the perforation density on the value of Mises stress decreases with the increase of the perforation phasing degree, and the maximum perforation stress is inversely related to the perforation phasing degree. This study is of great significance to prolong the service life of perforated casing in heavy-oil thermal recovery wells and to ensure normal production operation.

Key words: heavy-oil thermal recovery, casing damage, perforation, casing strength, stress con-centration

中图分类号:

TE357

梁疆岭, 杨洪, 苏宏益, 林铁军, 赵朝阳, 但晗. 稠油热采井射孔孔眼应力分析及影响因素[J]. 特种油气藏, 2024, 31(1): 152-158.

Liang Jiangling, Yang Hong, Su Hongyi, Lin Tiejun, Zhao Chaoyang, Dan Han. Stress Analysis and Influencing Factors of Perforation in Heavy-Oil Thermal Recovery Wells[J]. Special Oil & Gas Reservoirs, 2024, 31(1): 152-158.

参考文献

[1]田志华,海沙尔,生丽敏.射孔参数对套管强度影响的有限元分析[J]. 新疆石油天然气,2012, 8(增刊1): 101-103.
TIAN Zhihua,HAI Shaer,SHENG Limin.Analysis of finite element the influence of perforation parameters on the strength of casing[J]. Xinjiang Oil & Gas,2012, 8(S1):101-103.
[2]高娟, 樊伟, 姜向祖, 等. 螺旋布孔射孔对套管抗挤强度的影响分析[J]. 新疆石油天然气, 2008, 14(1): 56-58.
GAO Juan,FAN Wei,JIANG Xiangzu,et al.Effect of helix distributing perforation on casing col-lapsing strength[J].Xinjiang Oil & Gas,2008,14(1): 56-58.
[3]张立民. 冀东油田出砂井射孔套管变形分析[J]. 石油钻采工艺, 2013, 35(5): 71-73.
ZHANG Limin.Analysis on perforated casing deformation of sanding wells in Jidong Oilfield[J].Oil Drilling & Production Technology,2013,35(5):71-73.
[4]桂捷, 赵粉霞, 周志宏, 等. 射孔套管抗外挤剩余强度系数计算与拟合[J]. 石油天然气学报, 2014, 36(1): 154-157.
GUI Jie,ZHAO Fenxia,ZHAO Zhihong,et al.Computation and fitting of anti-sloughing of perfo-rated casing [J].Journal of Oil and Gas Technology,2014,36(1): 154-157.
[5]FARSI G A.Casing failures correlated with cementing quality in steam injection wells[C].SPE173483,2014:1-6.
[6]SHAIBI R A A. Mukhaizna steam injectors thermal efficiency & insulated tubing pilot evalua-tion[C].SPE172930,2015: 26-28.
[7]郑子君, 余成. 重复射孔对套管强度的影响[J].石油机械, 2017, 45(12): 100-105.
ZHENG Zijun, YU Cheng.Effect of repeated perforation on casing strength[J].China Petroleum Machinery,2017,45(12):100-105.
[8]唐庆, 步宏光, 饶富培, 等. 港西出砂油藏套损机理及预防对策研究[J]. 钻采工艺, 2019, 42(1): 28-30.
TANG Qing,BU Hongguang,RAO Fupei,et al.Deepening research on casing damage mechanism and preventive measures for Gangxi sand reservoir[J].Drilling & Production Technology,2019,42(1):28-30.
[9]贾立新, 陈毅, 韩耀图, 等. 基于多轮次吞吐套管安全性的射孔参数优选[J]. 石油机械, 2020, 48(11): 36-43.
JIA Lixin,CHEN Yi,HAN Yaotu,et al.Optimization of perforation parameters based on the casing safety after multiple huff and puff[J].China Petroleum Machinery,2020,48(11):36-43.
[10] 许杰, 贾立新, 陈毅,等.海上稠油热采井套管射孔参数设计[J]. 中国海上油气, 2020, 32(3): 118-123.
XU Jie,JIA Lixin,CHEN Yi,et al.Design of casing perforation parameters for offshore heavy oil thermal recovery wells[J].China Offshore Oil and Gas,2020,32(3):118-123.
[11] 慈建发, 刘献博, 李军, 等.基于套管损伤分析的射孔关键参数优化研究[J].石油管材与仪器, 2022, 8(2): 19-22.
CI Jianfa,LIU Xianbo,LI Jun,et al.Optimization of perforation key parameters based on casing damage analysis[J].Petroleum Tubular Goods & Instrument,2022,8(2):19-22.
[12] 韩耀图, 李进, 张磊, 等. 聚能射孔对水泥环的冲击损伤实验及数值模拟[J]. 石油机械, 2019, 47(8): 1-7.
HAN Yaotu,LI Jin,ZHANG Lei,et al.Experiment and Numerical Simulation on the Damage to the Cement Sheath during Shaped Perforation[J]. China Petroleum Machinery,2019,47(8):1-7.
[13] 王建军, 杨尚谕, 薛承文, 等.稠油热采井套管柱应变设计方法[J]. 中国石油大学学报(自然科学版), 2017, 41(1): 150-155.
WANG Jianjun,YANG Shangyu,XUE Chengwen,et al.Strain design method for casing strings in heavy oil thermal recovery well[J].Journal of China University of Petroleum(Edition of Natural Science),2017,41(1):150-155.
[14] 王建军, 杨尚谕, 纪海涛, 等.基于应变数值分析的稠油热采井套管优选[J]. 石油管材与仪器, 2019, 5(1): 42-45.
WANG Jianjun,YANG Shangyu,JI Haitao,et al.Optimum selection of casing for thermal recovery of heavy oil well based on strain numerical analysis[J].Petroleum Tubular Goods & Instru-men,2019,5(1):42-45.
[15] 肖遥, 邓金根, 刘伟, 等.射孔参数对热采井套管抗热应力能力影响分析[J]. 科学技术与工程, 2020, 20(13): 5094-5100.
XIAO Yao,DENG Jin′gen,LIU Wei,et al.Analysis on the effect of perforating parameters on thermal stress resistance of thermal production casing[J].Science Technology and Engineering, 2020,20(13):5094-5100.
[16] 熊佩, 胡艾国.射孔关键参数对水平井产能的影响[J].石油化工应用, 2013, 32(4): 78-81.
XIONG Pei,HU Aiguo.Influence of perforation parameter on productivity of horizontal well[J].Petrochemical Industry Application,2013,32(4):78-81.
[17] 唐汝众, 王同涛, 闫相祯, 等.射孔参数对套管强度影响的有限元分析[J].石油机械, 2010, 38(1): 32-34.
TANG Ruzhong,WANG Tongtao,YAN Xiangzhen,et al.Finite element analysis of the effect of perforation parameters on casing strength [J].China Petroleum Machinery,2010,38(1):32-34.
[18] 张永贵,李子丰,张立萍,真空隔热套管井筒套管强度研究[J].工程力学,2010,27(5):179-183.
ZHANG Yonggui,LI Zifeng,ZHANG Liping.Study on the casing strength of vacunn insulated shaft[J].Engineering Mechanics,2010,27(5):179-183.
[19] 刘建军,曾流芳,纪估军,等.热采井套管损坏力学机理及数值模拟[M].北京:科学出版社,2013:1-15.
LIU Jianjun,ZENG Liufang,JI Youjun,et al.Mechanical mechanism and numerical simulation of casing damage in thermal production oilfield[M].Beijing:Science Press,2013:1-15.

稠油热采井射孔孔眼应力分析及影响因素

Stress Analysis and Influencing Factors of Perforation in Heavy-Oil Thermal Recovery Wells

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	李爱芬, 高子恒, 景文龙, 付帅师. 基于CT扫描的蒸汽驱岩心孔隙结构特征及相渗分析[J]. 特种油气藏, 2023, 30(1): 79-86.
[2]	王国栋. 稠油热采伴生气物质来源及影响因素[J]. 特种油气藏, 2022, 29(3): 64-68.
[3]	张潇, 刘欣佳, 田永东, 张遂安, 连浩宇, 郑伟博, 马雄强. 水力压裂支撑剂铺置形态影响因素研究[J]. 特种油气藏, 2021, 28(6): 113-120.
[4]	蒋海岩, 李天月, 杜坤, 袁士宝, 张喻鹏. 火驱过程中稠油组分变化特征研究[J]. 特种油气藏, 2021, 28(4): 96-101.
[5]	李宗锟. 稠油热采井套管损坏机理及套管挂片技术实验[J]. 特种油气藏, 2021, 28(2): 171-174.
[6]	宋志军, 汪泓, 张铭, 张晨剑, 张明波. 高温井下温压数据声传直读监测技术[J]. 特种油气藏, 2020, 27(4): 163-167.
[7]	霍进, 吕柏林, 杨兆臣, 卢迎波, 胡鹏程. 稠油油藏多元介质复合蒸汽吞吐驱油机理研究 [J]. 特种油气藏, 2020, 27(2): 93-97.
[8]	高岳，姜瑞忠，崔永正，张春光，潘红. 牛顿流体-幂律流体双区复合稠油油藏水平井热采试井模型[J]. 特种油气藏, 2019, 26(4): 113-.
[9]	方舟，张彩旗，罗义科，吴金涛，屈继峰. 基于模糊数学的海上稠油热采效果评价研究及应用[J]. 特种油气藏, 2018, 25(1): 129-.
[10]	董长银，张清华，郑华安，董云彬，何海峰. 稠油热采防砂井动态产能评价方法及其应用[J]. 特种油气藏, 2016, 23(6): 123-.
[11]	刘新光，田冀，李娜，王磊，蔡柳. 海上稠油热采开发经济界限研究[J]. 特种油气藏, 2016, 23(3): 106-.
[12]	孙逢瑞，黄世军，邹明. 过热蒸汽吞吐水平井产能评价模型[J]. 特种油气藏, 2016, 23(3): 122-.
[13]	赵修太，付敏杰，王增宝，董林燕，唐金玉. 稠油热采调堵体系研究进展综述[J]. 特种油气藏, 2013, 20(4): 1-4.
[14]	黄颖辉，刘东，罗义科. 海上多元热流体吞吐先导试验井生产规律研究[J]. 特种油气藏, 2013, 20(2): 84-86.
[15]	吴拓王杨齐先有王贺. 齐40块蒸汽驱伴生气回注油藏效果分析[J]. , 2012, 19(1): 1-.